[Appendix B] B.4 Trace Statements

TCP/IP Network Administration

TCP/IP Network AdministrationSearch this book
Previous: B.3 Directive StatementsAppendix B
A gated Reference
Next: B.5 Options Statements
 

B.4 Trace Statements

Trace statements allow you to control the trace file and its contents from within the gated.conf file. The trace statement is:

traceoptions ["trace_file" [replace] [size bytes[k|m] files n]] [nostamp] trace_options [except trace_options] ;

Its components are as follows:

trace_file

Identifies the file that receives the trace output. It has exactly the same function as the trace_file argument on the gated command line.

replace

Replaces the existing trace file. If you do not use this keyword, the trace output is appended to the current contents of the file.

size bytes[k|m] [files n]

Limits the trace file to a maximum size of bytes. The optional k or m indicates thousands (k) or millions (m) of bytes. Thus 1000000 and 10m are equivalent entries. The size of the trace file cannot be less than 10k bytes. n defines the maximum number of trace files that should be saved. When the trace file reaches the maximum size, it is saved as trace_file.0, trace_file.1, trace_file.2 up to trace_file.n. The next save then overwrites trace_file.0. The value for n must be at least 2.

nostamp

Specifies that trace lines should not begin with a timestamp. Timestamping each line of trace data is the default.

trace_options

Define the events to be traced by gated. Each trace option is specified by a keyword name. The available trace options are:

none

Turns off all tracing.

all

Turns on all types of global tracing.

general

Turns on both normal and route tracing.

state

Traces state machine transitions for protocols such as OSPF and BGP. The RFCs describe these protocols using finite state machine (FSM) diagrams or tables. The protocols transition from one state to another based on the occurrence of certain events. For example, the state might change from idle to connect when a connection open event occurs. This is a highly specialized trace flag, useful only to those who have a thorough understanding of the protocols involved. Use this option within the protocol statement to trace a specific protocol's transitions.

normal

Traces normal protocols interactions. Errors are always traced.

policy

Traces the application of routing policies. Use this to check that you have properly configured your routing policy.

task

Traces system-level processing.

timer

Traces the various timers used by a protocol or peer.

route

Traces routing table changes. Use this to check that routes are properly installed by the protocol.

detail

Traces the contents of the packets exchanged by the router. Must be specified before send or recv.

send

Limits the detail trace to packets sent by this router.

recv

Limits the detail trace to packets received by this router. Without these two options, all packets are traced when detail is specified.

symbols

Traces the symbols read from the kernel at startup. See the -t command-line argument.

iflist

Traces the kernel interface list. See the -t command-line argument.

parse

Traces the lexical analyzer and parser.

adv

Traces the allocation and release of blocks.

except trace_options

Disables specific trace options. Must be used in conjunction with trace_options that enable a wide variety of tracing. For example: traceoptions all except state turns on all traces except for finite state machine tracing.

gated provides the flexibility for you to choose where you want to control tracing - on the command line or in the configuration file. By and large, the same trace options can be set on the gated command line or in the configuration file. detail, send and recv can be set only in the configuration file.

Two others, symbols and iflist, are primarily used on the command line. Refer to the section on the gated command line for a description of setting trace options with -t.

Some trace options are only useful for protocol developers and other experts. For most of us, general, which enables normal and route tracing, is an appropriate level of information for debugging routing problems. Occasionally policy is useful for testing a routing policy. Most of the time, however, no tracing is needed.


Previous: B.3 Directive StatementsTCP/IP Network AdministrationNext: B.5 Options Statements
B.3 Directive StatementsBook IndexB.5 Options Statements